| |
|
|
Lightning Protector RF Coaxial Lightning Protector |
|
|
Lightning Protector
|
RF Coaxial Lightning Protector |
|
| |
LP N MALE TO N FEMALE |
RF Lightning Protector |
|
Item number : WL-LA-NP-NJ |
|
The Lightning Surge Protectors listed on this page may also be referred to as: lightning suppressor, transient protector, spike arrestor, surge arrestor, lightning arrestor, spike protector, surge protector, lightning protector, spike suppressor, rf protector. Spelling of these products may also vary depending on location such as: lightning surge protecter, rf protecter, lightning suppresser, spike suppresser, spike arrester, surge arrester, and lightning arrester.
|
|
DC breakdown voltage: 230 +/- 20% (100V/s speed) |
|
Pulse breakdown voltage: <600V (100V/s speed) |
|
AC current range: 20A |
|
Pulse current range: 200A |
|
Overvoltage protection: >150V (100mA, <150ms) |
|
Isolation resistor: 1000m ohms |
|
Transmission loss: -1.5dB |
|
Frequency range: DC 2500MHz |
|
Gap can: 1.5P |
|
| |
|
| |
|
|
2.4Ghz Signal splitters
|
2.4Ghz Signal splitters |
|
|
2.4Ghz signal splitters(two way) |
Outdoor 2.4Ghz signal splitters N female |
|
| Item number : WLSP-2450-2W |
| |
Two way for wireless outdoor 2.4Ghz signal splitter.
Connector type: N female |
| WLSP-2450-2W is a two-port antenna splitter that enables you to operate one radio with two antennas. It is optimized for maximum performance in the 2.4 GHz band.
The model WLSP-2450-2W incorporates state of the art “microstrip” technology using the “Wilkinson” circuit topology. No power supply is required for operation of this splitter. |
Features |
|
Waterproof enclosure |
|
Works equally well for both transmit and receive signals |
|
Standard N-female connectors |
|
Includes pole mounting hardware |
|
Works with both FHSS and DSSS radio signals |
|
Covers the entire 2.4 GHz band |
|
Only 0.7 dB insertion loss over the theoretical 3dB loss found in 2 port splitters |
|
VSWR < 1.5:1 |
|
Supports up to 2 Watt transmitter power |
|
Extremely reliable stripline matching |
|
Passes DC through it to enable dual amplifiers (one for each antenna) |
|
Suitable for Omni or directional antennas or a combination thereof |
|
Provides isolation between the output ports |
|
Will not cause interference-producing intermodulation |
|
| |
| |
|
|
Power Booster
|
Wlan & Wi-Fi 802.11b/g Booster
FCC & CE |
|
|
|
Power Booster
|
Wlan & Wi-Fi 802.11b/g Booster
FCC & CE |
|
Item number : WLIB-BG24-500 |
|
SMA type Indoor WLAN 802.11b/g 500mW Power Booster
Alumine housing
6V
|
| Specification:
Output Power: 500mW
Operating Range 2400 - 2500 MHz
Operating Mode Bi-directional, half-duplex Time Division Duplex(TDD) Senses RF carrier from Transmitter and Automatically Switch receive to transmit mode
Transmit Gain 17dB Nominal (Spec. by customer)
Output Power: 500mW (+27dBm) nominal
TX Input Power 6dBm nominal (Spec. by customer)
Receiver Gain 10dB typical
Noise Figure 3.5dB typical
Connector SMA (50 ohm)
Power Consumption 360 mA ~ 420 mA
Operating Temp. -20 to +70 ?
Operating Humidity Up to 95% relative humidity
Material Die Casting Aluminum
Dimension (cm) 7.8cm(L) x 5.6cm(W) x 2.9cm(H)
Packaging Single/Gift Box: 22cm(L) x 15cm(W) x 6cm(H) W/Booster, Power Adapter, Cable(30cm)
Safety Certification FCC/CE/ |
|
| |
|
